Fundamental Plumbing Insights for Installing a Bathtub
Fundamental Plumbing Insights for Installing a Bathtub
Blog Article
Presented here down the page you can discover a lot of helpful ideas concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't exactly rocket science, yet it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a new one is additionally a moderately challenging job. If the old bathtub is easily accessible, the task can move immediately; if you have to open up a wall to remove the old bathtub as well as position the new bath tub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and also fit attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is much better to consider using one before you begin. Chances are you might require a specialist plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your shower room if you have already purchased a brand-new bathtub and also don't need to alter the setup of your previous supply of water pipelines.
Your tools and material checklist should comprise the following:
Planning for the Installation
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the restricted gain access to that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth all set for the remaining water that will come from the pipes. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water as well as check all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill up the tub as well as likewise check the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bathtub has actually been utilized at least once as this will resolve it into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers are in area between the faucet and the sink. Protect the faucet in place with the producer given backnut. When the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealant can split rather very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our article about Installing A Bathtub. Thank you so much for taking time to browse our article. Sharing is caring. Who knows, you might be helping someone out. Thanks for your time. Come back soon.
24/7 emergency? We're here! Report this page